Parts

The Dell 9F3GY (Dell internal part number 09F3GY, OEM Intel model SSDSC2BX800G4R) is an 800GB enterprise-grade SATA solid-state drive (SSD) from the Intel DC S3610 Series, fully rebranded, firmware-tuned, and rigorously validated by Dell for seamless integration into PowerEdge servers and compatible Dell/EMC storage platforms.
This drive belongs

The Dell 0Y3344 (also listed as Y3344 or cross-referenced with QLogic OEM part QLE2692) is a dual-port 16 Gigabit Fibre Channel Host Bus Adapter (HBA) — a high-performance storage networking card from the QLogic 2692 series, rebranded and fully certified by Dell for use in PowerEdge servers and Dell EMC storage environments.

Product Description

This is a PCIe-based 16Gb FC HBA that provides two independent 16 Gbps Fibre Channel ports (32 Gbps aggregate) for connecting servers to FC SAN fabrics, storage arrays (e.g., Dell EMC Unity, PowerStore, PowerMax, XtremIO, Compellent SC series), or tape libraries. It is backward compatible with 8 Gb/s and 4 Gb/s FC speeds, allowing seamless integration into existing SANs during transitions.

The card uses QLogic's 2692 ASIC (enhanced Gen5 technology), delivering:

• High IOPS (up to ~650K–1.3M IOPS in some configurations)
• Low CPU overhead via hardware offloads
• Full support for NPIV (N_Port ID Virtualization), boot from SAN, error recovery, and end-to-end data integrity
• Advanced features like FCoE readiness (firmware-dependent) and virtualization acceleration

It is a low-profile PCIe card (half-height bracket included; full-height optional) commonly used in Dell PowerEdge 13G–15G servers for SAN boot, high-throughput storage access, or multipathing (MPIO) setups. Dell validates it with custom firmware for seamless iDRAC/OpenManage monitoring, proper LED behavior, and compatibility with PERC controllers (when used in pass-through mode).

to Intel’s Data Center SSD family (DC S3610), a mixed-use (MU) / read-intensive optimized model built on Intel 3D MLC NAND (32-layer or later production runs), delivering exceptional performance, high endurance, and full power-loss protection (PLP) for mission-critical workloads in legacy server environments.
It is one of the most widely deployed SATA SSDs in Dell’s 11th–13th generation PowerEdge servers (and many 14G configs), particularly favored as a boot/OS drive, read caching layer, general-purpose performance tier, or VDI/web/analytics workload accelerator where cost-per-GB, reliability, and low power/heat are prioritized over maximum random write IOPS.

The Dell EMC 100-564-837 is a 1U sliding rack rail kit (commonly referred to as ReadyRails or universal sliding rails) designed for mounting 1U Dell EMC servers and certain 1U networking devices in standard 19-inch server racks.
This kit provides a smooth, full-extension sliding mechanism that allows the server to be pulled completely out of the rack for easy servicing, cabling, component replacement, or upgrades without needing to unmount or lift the entire unit. It is a tool-less or minimal-tool design for rapid installation in most rack types, making it one of the most commonly used rail solutions for Dell EMC 1U hardware in enterprise data centers, server rooms, and IT environments.

The 100-564-837 consists of a pair of adjustable, telescoping steel rails (left and right sides) with quick-release latches, snap-in mounting points, and included hardware for secure attachment. The rails extend fully, allowing complete server access while remaining safely supported in the rack.
It supports both 2-post (telco-style) and 4-post racks, with compatibility for:

Square-hole racks (tool-less snap-in installation)
Round-hole unthreaded racks (using cage nuts and screws)
Threaded racks (using provided screws)

The kit is adjustable to fit a wide range of rack depths (typically spanning ~631–868 mm or 24.8–34.2 inches), making it versatile for most standard 19-inch EIA-310 compliant racks from Dell and third-party manufacturers.
This rail kit is most frequently associated with Dell EMC PowerEdge 13th and 14th generation 1U servers (e.g., R630, R640, R430, R440, R330, R340), but it is backward compatible with many 13G models in square-hole or threaded racks. It is also used with some 1U Dell EMC networking switches (e.g., S4112 series).

The CX354A features two QSFP ports, each capable of operating in either 40 Gb/s Ethernet mode or 56 Gb/s FDR InfiniBand mode (40 Gb/s effective data rate with IB overhead). The VPI (Virtual Protocol Interconnect) technology allows each port to be independently configured for Ethernet or InfiniBand, providing maximum flexibility in hybrid or multi-protocol environments.
In EMC/Isilon deployments, this card was one of the most commonly used cluster interconnect NICs in Isilon H-series (hybrid) and F-series (all-flash) nodes, enabling ultra-fast node-to-node communication across the scale-out NAS cluster. It supports RDMA (Remote Direct Memory Access) over both native InfiniBand and RoCE (RDMA over Converged Ethernet), delivering near-zero CPU overhead and sub-microsecond latencies for data transfers.
The card includes extensive hardware offloads for TCP/UDP/IP stateless processing, large send offload (LSO), receive side scaling (RSS), iSCSI/SMB Direct acceleration, FCoE (Fibre Channel over Ethernet), and advanced virtualization features like SR-IOV (up to 127 virtual functions per port).

The NetApp FAS2240 (and the closely related FAS2220) is a compact, entry-level/mid-range unified storage controller from NetApp’s FAS2000 series, released around 2011–2012. It is a 2U rack-mountable dual-controller system designed for small to medium businesses, remote offices, and departmental deployments.

The FAS2240 / FAS2220 is a unified storage platform that supports both block (iSCSI, FC, FCoE) and file (NFS, CIFS/SMB) protocols in a single system. It comes with dual active/active controllers for high availability and uses ONTAP operating system.

Key hardware characteristics of the FAS2240:

• 2U chassis with 24 × 2.5" SFF or 12 × 3.5" LFF drive bays (model dependent)
• Dual controllers (active/active HA pair)
• Onboard ports: 4 × 1 GbE + 2 × 10 GbE (or 8 Gb FC depending on configuration)
• Expansion: Supports external disk shelves (DS2246, DS4243, etc.)
• Performance: Suitable for light to moderate workloads — virtualization, file sharing, backup targets, small databases, VDI, etc.

The FAS2220 is the lower-end variant with slightly reduced performance and port options compared to the FAS2240, but they share the same chassis and many components.

NETAPP 111-04373+D0 SAS Disk Array Controller Module

The NetApp 114-00063 (also listed as 114-00063+A0 or X758-R6 in some references) is an 850W (891W peak) AC power supply unit (PSU) designed for the NetApp FAS3000 series controllers, specifically the FAS3140, FAS3160, and FAS3170 systems (and compatible with some FAS3240 configurations).

This is a rear-mounted, hot-swappable redundant power supply that provides 850W continuous output power (up to 891W peak) to the FAS3140/3160/3170 controller enclosure. It is engineered for high-availability storage systems running ONTAP, supporting dual-controller HA pairs with N+1 redundancy.

The PSU accepts universal AC input (100–240V) and delivers multiple regulated DC rails to the midplane for controllers, drives, fans, and I/O modules. It features an integrated cooling fan with front-to-back airflow (matching the FAS3000 chassis direction) and clear LED status indicators (AC OK, DC OK, Fault).

In typical deployments, the FAS3140/3160/3170 uses two PSUs in a redundant configuration — allowing live replacement of a failed unit without downtime.

EMC 118033270 350GB SSD PCIe MLC Add-In Card

IBM zEnterprise IBM 11S45D08 Evaporator Assembly, refrigerated Heatsink.