Parts

The IBM 00E6367 (also listed with CCIN 2BF8 and alternate part 00RR726) is a Processor Voltage Regulator Module (VRM) specifically designed as VRM-PROC2-CJ — a power regulation subassembly for the processor book (CPU complex) in high-end IBM Power Systems servers.

This is a DC-DC voltage regulator module that steps down bulk power from the server's main power supplies to precise, stable low-voltage rails required by POWER7 processors and associated memory/cache subsystems in the CEC (Central Electronics Complex). It is part of the PROC2 (Processor 2) voltage regulation group — one of several VRMs per processor book that work in parallel to deliver high current with redundancy and load sharing.

In high-end IBM Power Systems, each processor book (also called processor card or CPU book) contains multiple VRMs to support multi-core POWER7 SCMs (Single-Chip Modules) and large memory configurations. The 00E6367 / VRM-PROC2-CJ is a critical component in the power distribution chain — failure of this module can cause:

• Processor throttling or clock-down
• Voltage instability
• System crashes or boot failures
• Reduced performance under load
• Redundancy loss (N+1 or N+N configuration)

The module includes integrated protection (over-current, over-voltage, over-temperature), monitoring circuitry, and status LEDs. It is hot-swappable in redundant setups (when other VRMs can compensate) and is monitored via the Hardware Management Console (HMC) and ASMI (Advanced System Management Interface).

00YC321 LENOVO 200GB 6G SFF SATA SSD

The IBM 01EM868 is the official side rail kit (also known as rack mounting rails or slide rails) designed specifically for the IBM Power System IC922 (machine type 8335-GTG / 8335-GTH), a high-performance 2U rack server from the POWER9 generation (launched 2018–2019).

This is a tool-less, full-extension sliding rail kit that allows the IBM Power IC922 server to be securely mounted in a standard 19-inch EIA-310 rack while providing smooth, full server pull-out for easy servicing, cabling, component replacement, or upgrades without removing the server from the rack.

The kit consists of:

• Left and right telescoping rails
• Quick-release latches
• Tool-less snap-in mounting points (for square-hole racks)
• Included hardware for round-hole/threaded racks (cage nuts, screws, adapters)
• Installation instructions

It is adjustable to fit a wide range of rack depths (typically ~631–868 mm / 24.8–34.2 inches), making it compatible with most standard 19-inch racks (Dell, HPE, APC, Rittal, etc.). The rails support front-to-back or back-to-front airflow configurations and include safety stops to prevent accidental full removal.

This rail kit is essential for proper racking of the IC922 — it is the IBM-validated solution that ensures mechanical stability, proper alignment with the chassis, and compliance with IBM rack-mount specifications (especially important for heavy 2U POWER9 servers with multiple GPUs, large memory, or high-power PSUs).

Dell 01HGDK EMC Poweredge R740 16-Bay SFF Server Backplane Expander

The Lenovo 01KR353 is a 16GB DDR4-2933 Registered ECC Memory module (RDIMM). It is a genuine Lenovo ThinkSystem / TruDDR4 enterprise memory module, with Samsung OEM equivalent M393A2K40CB2-CVFCO.

This is a Single Rank x4 (1Rx4) 16GB DDR4 RDIMM running at 2933 MHz (PC4-23400). It is optimized for Lenovo ThinkSystem servers and provides excellent performance with lower power consumption compared to higher-rank modules. The module is fully validated by Lenovo for stability and compatibility in their latest server platforms.

The IBM 01LJ138 is the official hot-swap drive caddy (also called LFF hard drive tray, carrier, or sled) for 3.5-inch Large Form Factor (LFF) drives in the IBM Storwize V7000 Gen2 (models 2076-524/624/724) and Storwize V9000 systems (and compatible expansion enclosures).

This is a tool-less, hot-swappable drive tray designed to securely hold and mount standard 3.5-inch SAS/SATA HDDs or SSDs into the Storwize V7000 Gen2 or V9000 front drive bays. It features:

• Black plastic/metal construction with a spring-loaded latch
• ESD (electrostatic discharge) protection
• Vibration-dampening mounts to reduce drive wear in dense enclosures
• LED pass-through for drive activity/fault indicators
• Alignment pins/guides for fool-proof insertion into the backplane

The caddy is mandatory for installing or replacing drives in these systems — bare drives cannot be inserted directly. It is the exact same tray used in most IBM Storwize V7000 Gen2 and V9000 enclosures (24-bay LFF or 12-bay LFF configurations).

Failure to use the correct tray (or using a mismatched tray from V7000 Gen1, V5000, or other vendors) can cause:

• Drive not detected
• Backplane connection failure
• Vibration-induced errors
• Improper seating or ejection

This tray is a very common FRU (Field Replaceable Unit) when trays are lost, damaged, cracked, or worn out during drive replacements.

The IBM 01LJ126 is a hot-swap fan module (also listed as fan FRU or cooling module) designed specifically for the IBM Storwize V5000 Gen2 storage systems, particularly the 92F model (24-bay 2.5-inch SFF enclosure) and related expansion units in the V5000 Gen2 family.

This is a high-speed, redundant fan assembly that provides active cooling for the Storwize V5000 Gen2 controller enclosure or expansion enclosure (92F = 2.5" SFF 24-drive canister). The module contains multiple high-RPM fans arranged in a single replaceable tray, with integrated airflow direction optimized for front-to-back cooling in the enclosure.

Key characteristics:

• Hot-swappable design — can be replaced without powering down the enclosure when redundancy is maintained (N+1 fan redundancy typical in V5000 Gen2)
• Built-in fault detection and reporting to the Storwize firmware (via LED status and system alerts in GUI/CLI)
• Tool-less insertion/removal with latch mechanism
• Front-to-back airflow (cold aisle intake, hot aisle exhaust)
• Low acoustic noise profile for data center environments

Failure of a fan module typically triggers:

• Amber fault LED on the module
• Enclosure fault light
• Critical alert in Storwize GUI / CLI / email / SNMP
• Potential thermal throttling or enclosure shutdown if multiple fans fail

Replacement restores full cooling redundancy and prevents overheating of drives, controllers, or cache batteries.

The IBM 01PL480 (also cross-referenced with part numbers 00VJ951, 38L7509, and alternate 01PL863) is an IBM LTO-7 Half-High (HH) SAS tape drive with an integrated single-slot loader (autoloader mechanism), designed for rack-mount or standalone tape automation in entry-level to midrange backup, archiving, and compliance environments.

This is a 1U rack-mountable LTO-7 tape solution that combines one LTO-7 HH SAS tape drive with a built-in 8-slot magazine loader, allowing automated backup/restore of up to 8 cartridges without manual intervention. It is ideal for small-to-medium businesses, branch offices, departmental servers, or remote sites needing cost-effective unattended tape backup, offsite vaulting, or long-term archival storage.

The drive uses Linear Tape-Open (LTO) Ultrium 7 technology, delivering:

• 6 TB native capacity per cartridge
• 15 TB compressed capacity per cartridge (typical 2.5:1 compression ratio; real-world 2–2.5:1)
• 300 MB/s native transfer rate (up to 750 MB/s compressed)

The integrated loader supports barcode scanning, sequential or random access to cartridges, and automatic cartridge loading/unloading via SCSI commands — making it function as a very small autoloader with one drive and 8 slots. It is fully compatible with major backup software (IBM Spectrum Protect, Veeam, Veritas NetBackup, Commvault, ARCserve, etc.) and supports LTFS (Linear Tape File System) for drag-and-drop file access.

This unit is a direct replacement or upgrade for older LTO-5/LTO-6 HH autoloaders and is commonly used in IBM TS2900/TS3100/TS3200-compatible rack setups or as a standalone desktop/1U solution.